P22EE — Cylinder 6 alternative fuel injector: control signal too low
| Meaning | The control unit measured a lower voltage than expected on the control circuit of the cylinder 6 alternative fuel injector (for example the gas injector on a bi-fuel system). This usually means a wire is shorting to ground through damaged insulation, or the injector or its driver inside the control unit is drawing current abnormally. Often the problem is the wiring, not the injector. |
| Family | Powertrain (P) |
Typical symptoms
Rough or jerky running on the alternative fuel
Loss of power
The car stays on or switches back to the normal fuel
Smell of unburnt fuel from the exhaust
Common causes
Dirty, wet or corroded injector connector
Injector with a shorted internal winding
Wiring pinched or rubbed near hot or moving parts
Faulty driver stage in the control unit (rare)
What to do
How to read code P22EE
This is a warning: the vehicle usually keeps working, but the control unit may limit performance (limp mode) until the fault is removed.
The code P22EE starts with P: it belongs to the powertrain (engine and transmission) area. It is defined by the SAE/ISO standard, so it means the same on every make. The third character (2) points to fuel and air metering (injector circuit), and the last two (EE) identify the specific fault inside that group.
How to proceed, in order
- Read the code with the diagnostic tool and note the freeze-frame data and any other stored codes.
- Check connectors, wiring and grounds of the component involved, and the battery voltage.
- Measure the real values of the component with the diagnostic tool instead of replacing it by guesswork.
- After the repair, clear the code and confirm with a road test that it does not come back.
Frequently asked questions
What does code P22EE mean?
Cylinder 6 alternative fuel injector: control signal too low. The control unit measured a lower voltage than expected on the control circuit of the cylinder 6 alternative fuel injector (for example the gas injector on a bi-fuel system). This usually means a wire is shorting to ground through damaged insulation, or the injector or its driver inside the control unit is drawing current abnormally. Often the problem is the wiring, not the injector.
Can I keep driving with code P22EE active?
With caution: limp mode possible, have it checked soon
Common causes — P22EE
Control wire with damaged insulation touching ground Dirty, wet or corroded injector connector Injector with a shorted internal winding Wiring pinched or rubbed near hot or moving parts Faulty driver stage in the control unit (rare)
How do you fix code P22EE?
First check the connector and wiring of the cylinder 6 injector, looking for chafed wires, moisture and blackened terminals. Then the injector resistance and the wire's insulation to ground should be tested. You can use the normal fuel, but have it checked soon.
We are ECU specialists: diagnosis, file repair and remapping for cars, bikes, trucks and agricultural vehicles.
Write to us on WhatsApp Contact us- Previous code: P22ED — Cylinder 6 alternative fuel injector: open circuit
- Next code: P22EF — Cylinder 6 alternative fuel injector: control sign...
Related codes
- P2200 — NOx sensor circuit fault, bank 1
- P2201 — NOx sensor circuit range/performance, bank 1
- P2202 — NOx sensor circuit low input, bank 1
- P2203 — NOx sensor circuit high input, bank 1
- P2204 — NOx sensor intermittent signal, bank 1
- P2205 — NOx sensor heater control circuit open, bank 1
- P2206 — NOx sensor heater control circuit low, bank 1
- P2207 — NOx sensor heater control circuit high, bank 1
- P2208 — NOx sensor heater sense circuit, bank 1
- P2209 — NOx sensor heater sense circuit out of range, bank 1
- P220A — Speed signal comparison implausible, Y3/6n2 and Y3/6n3
- P220B — Speed too high, Y3/6n2 or Y3/6n3