Car fault codes: 27,548 DTC explained
Meaning, severity, whether you can keep driving and what to check, for OBD-II standard codes and for the native codes of VAG, BMW, MAN, Mercedes-Benz, Renault, Ford and Dodge. Type the code your tool shows.
How to read a code
An OBD-II code has five characters, and each one says something. Take P0401, one of the most looked-up codes:
The four families of standard codes
Every family has its own list, in code order, with the meaning next to each code.
Native codes are a different language
VAG units store five-digit codes (00275), BMW units use hexadecimal ones (2A6F, 4C5E), MAN and Mercedes-Benz have their own tables. They are read with a diagnostic tool that speaks the manufacturer protocol, not with a generic OBD reader, and they are listed here by manufacturer.
How serious it is
Every code carries a severity and an answer to the question that matters when the warning light comes on: can I keep driving? The numbers are how many codes fall in each level.
- Informational 586
An informational entry: it normally does not limit how the vehicle works.
- Warning 25,380
The vehicle usually keeps working, but the control unit may limit performance (limp mode) until the fault is removed.
- Serious 1,452
Driving behaviour may get worse or other components may be damaged if the vehicle is used without checking it.
- Critical 130
Vehicle safety or integrity may be compromised: diagnosis should not be postponed.
What to do when a code appears
- Read the code with the diagnostic tool and note the freeze-frame data and any other stored codes.
- Check connectors, wiring and grounds of the component involved, and the battery voltage.
- Measure the real values of the component with the diagnostic tool instead of replacing it by guesswork.
- After the repair, clear the code and confirm with a road test that it does not come back.
Clearing a code without repairing the cause only turns the light off until the next drive cycle. A remap does not fix a fault either: the cause is removed first.
Browse by manufacturer
11,969 standard OBD-II codes and 15,579 native codes of seven manufacturers.
Most looked-up codes
- P0299 — Turbocharger: underboost condition
- P0401 — EGR: insufficient recirculation flow
- P2002 — Diesel particulate filter (DPF) clogged
- P0402 — EGR: excessive recirculation flow
- P0093 — Fuel rail pressure: leak detected
- P0522 — Engine oil pressure too low
- 01802 · VAG — Door warning lamp, front passenger side-W36
- P0304 — Cylinder 4 Misfire Detected
- P0403 — EGR control circuit
- P0001 — Fuel Volume Regulator Control Circuit Open
- P0089 — Fuel pressure regulator: performance
- P0341 — Camshaft Position Sensor Circuit Range/Performance
- P0380 — Glow plug circuit
- P0404 — EGR: control circuit range/performance
- P1484 — Manufacturer-Specific Powertrain Fault P1484
- P2015 — Intake manifold runner control: implausible position
- P0087 — Fuel rail pressure too low
- P0245 — Turbocharger Wastegate Solenoid A Low
- P0409 — Exhaust Gas Recirculation Sensor A Circuit
- P0435 — Catalyst System Efficiency Below Threshold Bank 2
- P1800 — Manufacturer-Specific Powertrain Fault Code P1800
- U0001 — High Speed CAN Communication Bus
- 00016 · VAG — Rear right footwell/defrost flap actuator V195
- DF1012 · Renault — Coherences information multiplexed for RV / LV
- P0011 — Camshaft timing over-advanced (bank 1)
- P0045 — Turbocharger boost control circuit
- P00FC — Turbo outlet pressure sensor A: erratic signal
- P0128 — Engine does not reach operating temperature
- P0131 — O2 sensor bank 1 sensor 1: low voltage
- P0155 — Oxygen Sensor Heater Circuit Malfunction
- P0190 — Fuel rail pressure sensor circuit
- P0234 — Turbocharger: overboost condition
- P0301 — Cylinder 1 misfire
- P0335 — Crankshaft position sensor: circuit
- P0340 — Camshaft Position Sensor Circuit Malfunctioning
- P0420 — Catalyst efficiency below threshold
Frequently asked questions
What is a DTC?
A Diagnostic Trouble Code is the entry a control unit stores when a measured value leaves the range it expects, for example a sensor reading, a pressure or a signal that is missing. It identifies the area of the fault, not the part to replace.
How do I read an OBD-II code?
Five characters: a letter for the system (P powertrain, B body, C chassis, U network), a digit that says whether the code is standard (0) or manufacturer-defined (1), a digit for the subsystem and two for the component. P0401, for example, is a standard powertrain code of the emissions subsystem about EGR flow.
Why does my tool show a code that is not in the OBD-II list?
Because it is a native code: VAG units store five-digit codes, BMW units hexadecimal ones, MAN and Mercedes-Benz their own tables. They need a tool that speaks the manufacturer protocol. In this dictionary they are listed by manufacturer.
Can I just clear the code?
You can, but the light comes back as soon as the control unit measures the same fault again, usually within one drive cycle. Clearing is the last step after the repair, and a road test confirms that the code stays away.
The engine light is on: can I keep driving?
It depends on the code. Most codes let the vehicle run, often with reduced performance (limp mode); a few, such as oil pressure or brake faults, require stopping. Every page in the dictionary answers this question for its code.
Does a remap fix a fault code?
No. A remap changes the calibration, it does not repair a sensor, a valve or a wiring fault, and a persistent code should be solved first. Where a fault involves the control unit software itself, a MasterTuning workshop can diagnose it on the car.
Need help with a fault?
The authorised MasterTuning workshops diagnose on the car: ECU, DPF, EGR, AdBlue, injection and electrical faults.