P28C3 — EVAP high-load purge line B: performance out of range
| Meaning | The control unit checked the flow on purge line B while the engine was demanding a strong purge of fuel vapour, and it did not match what was expected. The EVAP system collects vapour from the fuel tank and feeds it to the engine to be burned. This code says that this line or its valve is not behaving correctly under load. Which line counts as B depends on the individual engine layout, so it must be confirmed on the vehicle's diagram. |
| Family | Powertrain (P) |
Typical symptoms
Smell of fuel near the car or the tank
Rough idle after refuelling
Slight hesitation or surge when accelerating
Hard starting when hot after refuelling
Possible failure of the emissions test
Common causes
Cracked, disconnected or blocked purge hoses
Saturated or clogged charcoal canister
Worn fittings or connectors on line B
EVAP pressure sensor giving wrong readings
Damaged wiring or connector at the valve
What to do
How to read code P28C3
This is a warning: the vehicle usually keeps working, but the control unit may limit performance (limp mode) until the fault is removed.
The code P28C3 starts with P: it belongs to the powertrain (engine and transmission) area. It is defined by the SAE/ISO standard, so it means the same on every make. The third character (8) points to transmission, and the last two (C3) identify the specific fault inside that group.
How to proceed, in order
- Read the code with the diagnostic tool and note the freeze-frame data and any other stored codes.
- Check connectors, wiring and grounds of the component involved, and the battery voltage.
- Measure the real values of the component with the diagnostic tool instead of replacing it by guesswork.
- After the repair, clear the code and confirm with a road test that it does not come back.
Frequently asked questions
What does code P28C3 mean?
EVAP high-load purge line B: performance out of range. The control unit checked the flow on purge line B while the engine was demanding a strong purge of fuel vapour, and it did not match what was expected. The EVAP system collects vapour from the fuel tank and feeds it to the engine to be burned. This code says that this line or its valve is not behaving correctly under load. Which line counts as B depends on the individual engine layout, so it must be confirmed on the vehicle's diagram.
Can I keep driving with code P28C3 active?
With caution: limp mode possible, have it checked soon
Common causes — P28C3
Purge valve stuck open, closed or half-open Cracked, disconnected or blocked purge hoses Saturated or clogged charcoal canister Worn fittings or connectors on line B EVAP pressure sensor giving wrong readings Damaged wiring or connector at the valve
How do you fix code P28C3?
Start with the fuel cap and the visible vapour hoses near the intake manifold and the tank, then have the purge valve tested with a diagnostic tool. You can drive for a short while, but do not put it off for long: fuel vapour is flammable and pollutes.
We are ECU specialists: diagnosis, file repair and remapping for cars, bikes, trucks and agricultural vehicles.
Write to us on WhatsApp Contact us- Previous code: P28C2 — Ion sense module supply voltage too high
- Next code: P28C4 — Clutch A motor U-V-W phase circuit: signal too low
Related codes
- P2800 — Range sensor B circuit (PRNDL input) fault
- P2801 — Range sensor B circuit: implausible signal
- P2802 — Range sensor B circuit: signal too low
- P2803 — Range sensor B circuit: signal too high
- P2804 — Range sensor B circuit: intermittent signal
- P2805 — Range sensors A and B: signals do not agree
- P2806 — Transmission range sensor: misalignment
- P2807 — Pressure control solenoid G circuit fault
- P2808 — Pressure solenoid G: performance fault or stuck off
- P2809 — Pressure solenoid G: stuck on
- P280A — Range sensor A circuit: not learned
- P280B — Transmission range sensor B: not learned