P20FC — Cylinder 10 spark plug or ignition, right bank (module N92/2)
| Meaning | The reference text points to a problem with the spark plug or ignition mode of cylinder 10, handled by ignition module N92/2 on the right cylinder bank. The wording is tied to a specific manufacturer (likely Mercedes), and I don't have solid information on the exact test the control unit runs. In practice, the ignition of that cylinder is not responding as it should. |
| Family | Powertrain (P) |
Typical symptoms
Rough idle
Hesitation or loss of power when accelerating
Smell of unburnt fuel from the exhaust
Higher fuel consumption than usual
Common causes
Faulty ignition coil on that cylinder
Corroded or damaged connector or wiring to module N92/2
Faulty ignition module N92/2
Moisture or oil in the spark plug well
What to do
How to read code P20FC
This is a warning: the vehicle usually keeps working, but the control unit may limit performance (limp mode) until the fault is removed.
The code P20FC starts with P: it belongs to the powertrain (engine and transmission) area. It is defined by the SAE/ISO standard, so it means the same on every make. The third character (0) points to fuel and air metering and auxiliary emission controls, and the last two (FC) identify the specific fault inside that group.
How to proceed, in order
- Read the code with the diagnostic tool and note the freeze-frame data and any other stored codes.
- Check connectors, wiring and grounds of the component involved, and the battery voltage.
- Measure the real values of the component with the diagnostic tool instead of replacing it by guesswork.
- After the repair, clear the code and confirm with a road test that it does not come back.
Frequently asked questions
What does code P20FC mean?
Cylinder 10 spark plug or ignition, right bank (module N92/2). The reference text points to a problem with the spark plug or ignition mode of cylinder 10, handled by ignition module N92/2 on the right cylinder bank. The wording is tied to a specific manufacturer (likely Mercedes), and I don't have solid information on the exact test the control unit runs. In practice, the ignition of that cylinder is not responding as it should.
Can I keep driving with code P20FC active?
With caution: limp mode possible, have it checked soon
Common causes — P20FC
Worn or fouled spark plug on cylinder 10 Faulty ignition coil on that cylinder Corroded or damaged connector or wiring to module N92/2 Faulty ignition module N92/2 Moisture or oil in the spark plug well
How do you fix code P20FC?
Have the plug, coil and connectors of cylinder 10 checked after reading the codes with a tool suited to your brand. If the engine is jerking, avoid hard acceleration to protect the catalytic converter. Don't put it off for long.
We are ECU specialists: diagnosis, file repair and remapping for cars, bikes, trucks and agricultural vehicles.
Write to us on WhatsApp Contact us- Previous code: P20FB — Cylinder 9 spark plug or ignition, right bank (mod...
- Next code: P20FD — Cylinder 11 spark plug or ignition, right bank (mo...
Related codes
- P2000 — NOx trap efficiency below threshold, bank 1
- P2001 — NOx trap efficiency below threshold, bank 2
- P2002 — Diesel particulate filter (DPF) clogged
- P2003 — Particulate filter efficiency below threshold, bank 2
- P2004 — Intake manifold runner control stuck open, bank 1
- P2005 — Intake runner control stuck open (bank 2)
- P2006 — Intake runner control stuck closed (bank 1)
- P2007 — Intake runner control stuck closed (bank 2)
- P2008 — Intake runner control circuit open (bank 1)
- P2009 — Intake runner control circuit low (bank 1)
- P200A — P200A: meaning is manufacturer dependent, needs verifying
- P200B — P200B: meaning is manufacturer dependent, needs verifying