P21DC — Cylinder 1 injector B circuit: signal too high
| Meaning | The engine control unit measured too high a voltage in the electrical circuit of the second injector (injector B) on cylinder 1. The code points to the wiring circuit and does not by itself prove the injector is faulty. Injector B is a second injector per cylinder, found only on dual-injection engines, and its exact position depends on the manufacturer. The cylinder may get the wrong amount of fuel, or none. |
| Family | Powertrain (P) |
Typical symptoms
Rough idle
Vibration or hesitation when accelerating
Loss of power
Hard or slow starting
Higher fuel consumption than usual
Common causes
Injector connector dirty, corroded or with bent pins
Cylinder 1 injector B with a failed internal coil
Wiring damaged by engine heat or rubbing
Faulty injector driver in the engine control unit (rare)
What to do
How to read code P21DC
This is a warning: the vehicle usually keeps working, but the control unit may limit performance (limp mode) until the fault is removed.
The code P21DC starts with P: it belongs to the powertrain (engine and transmission) area. It is defined by the SAE/ISO standard, so it means the same on every make. The third character (1) points to fuel and air metering, and the last two (DC) identify the specific fault inside that group.
How to proceed, in order
- Read the code with the diagnostic tool and note the freeze-frame data and any other stored codes.
- Check connectors, wiring and grounds of the component involved, and the battery voltage.
- Measure the real values of the component with the diagnostic tool instead of replacing it by guesswork.
- After the repair, clear the code and confirm with a road test that it does not come back.
Frequently asked questions
What does code P21DC mean?
Cylinder 1 injector B circuit: signal too high. The engine control unit measured too high a voltage in the electrical circuit of the second injector (injector B) on cylinder 1. The code points to the wiring circuit and does not by itself prove the injector is faulty. Injector B is a second injector per cylinder, found only on dual-injection engines, and its exact position depends on the manufacturer. The cylinder may get the wrong amount of fuel, or none.
Can I keep driving with code P21DC active?
With caution: limp mode possible, have it checked soon
Common causes — P21DC
Injector wiring shorted to a power supply Injector connector dirty, corroded or with bent pins Cylinder 1 injector B with a failed internal coil Wiring damaged by engine heat or rubbing Faulty injector driver in the engine control unit (rare)
How do you fix code P21DC?
Have the data read with a diagnostic scanner and first check the connector and wiring of cylinder 1 injector B for burns, moisture or exposed wires. If the engine hesitates or the warning light flashes, avoid heavy loads and stop as soon as you can, since uneven combustion can damage the catalytic converter. Do not clear the code: the fault stays and comes back.
We are ECU specialists: diagnosis, file repair and remapping for cars, bikes, trucks and agricultural vehicles.
Write to us on WhatsApp Contact us- Previous code: P21DB — Cylinder 1 injector B: circuit low
- Next code: P21DD — Reductant (AdBlue) heater: current too low
Related codes
- P2100 — Throttle actuator motor circuit open
- P2101 — Throttle actuator motor circuit range/performance
- P2102 — Throttle actuator motor circuit low
- P2103 — Throttle actuator motor circuit high
- P2104 — Throttle actuator control system forced idle
- P2105 — Throttle actuator control system forced engine shutdown
- P2106 — Throttle actuator control system forced limited power
- P2107 — Throttle actuator control module processor fault
- P2108 — Throttle actuator control module performance
- P2109 — Throttle/pedal sensor A minimum stop performance
- P210A — Starter lockout relay K38/3: short circuit or open wiring
- P210B — Throttle actuator B control motor circuit range/performance