P1122 — Throttle position sensor: intermittent low voltage
| Meaning | P1122 is a manufacturer-defined code. According to the reference definition, the control unit intermittently read too low a voltage from the throttle position sensor circuit. The control unit therefore sees the throttle closed or the signal vanish even when that isn't the case, or a wire touching ground. The fault comes and goes, so there's often a contact making a false connection. |
| Family | Powertrain (P) |
Typical symptoms
Engine stalling or nearly stalling when you lift off
Weak acceleration or flat spots
Low or irregular idle
Automatic gearbox shifting badly
Intermittent loss of power
Common causes
Connector with weak or corroded contact
Signal wire broken intermittently or touching ground
Poor sensor ground
Sensor loose or badly fitted
Dirty or loose throttle body
What to do
How to read code P1122
This is a warning: the vehicle usually keeps working, but the control unit may limit performance (limp mode) until the fault is removed.
The code P1122 starts with P: it belongs to the powertrain (engine and transmission) area. It is defined by the manufacturer, so the exact meaning can change from make to make. The third character (1) points to fuel and air metering, and the last two (22) identify the specific fault inside that group.
How to proceed, in order
- Read the code with the diagnostic tool and note the freeze-frame data and any other stored codes.
- Check connectors, wiring and grounds of the component involved, and the battery voltage.
- Measure the real values of the component with the diagnostic tool instead of replacing it by guesswork.
- After the repair, clear the code and confirm with a road test that it does not come back.
Frequently asked questions
What does code P1122 mean?
Throttle position sensor: intermittent low voltage. P1122 is a manufacturer-defined code. According to the reference definition, the control unit intermittently read too low a voltage from the throttle position sensor circuit. The control unit therefore sees the throttle closed or the signal vanish even when that isn't the case, or a wire touching ground. The fault comes and goes, so there's often a contact making a false connection.
Can I keep driving with code P1122 active?
With caution: limp mode possible, have it checked soon
Common causes — P1122
Worn track in the throttle position sensor Connector with weak or corroded contact Signal wire broken intermittently or touching ground Poor sensor ground Sensor loose or badly fitted Dirty or loose throttle body
How do you fix code P1122?
Check the connector, wires and ground of the sensor on the throttle body, moving the wires with the engine running to provoke the fault. Have the signal read with a tester while slowly pressing the pedal and look for sudden drops. If the engine has flat spots or risks stalling, avoid overtaking and heavy traffic and have it checked soon.
We are ECU specialists: diagnosis, file repair and remapping for cars, bikes, trucks and agricultural vehicles.
Write to us on WhatsApp Contact us- Previous code: P1121 — Throttle position sensor: intermittent high voltag...
- Next code: P1123 — Throttle position sensor: plausible but higher tha...
Related codes
- P1100 — Mass airflow (MAF) sensor signal intermittent
- P1101 — Mass airflow (MAF) sensor out of range in self-test / KOER a...
- P1102 — Mass airflow (MAF) sensor in range but lower than expected
- P1103 — Mass airflow (MAF) sensor in range but higher than expected
- P1104 — Mass airflow (MAF) sensor ground malfunction
- P1105 — Dual alternator system fault reported (upper unit)
- P1106 — Dual alternator lower fault / MAP sensor intermittent high v...
- P1107 — Dual alternator lower fault / MAP sensor intermittent low vo...
- P1108 — Battery lamp circuit, dual alternator: malfunction
- P1109 — Intake air temperature sensor B: intermittent signal
- P1110 — Intake air temperature sensor: open or short circuit
- P1111 — Intake air temperature sensor: intermittent high voltage