P1123 — Throttle position sensor: plausible but higher than expected
| Meaning | P1123 is a manufacturer-defined code. The reference definition indicates that the throttle position sensor gives a value within the normal range but higher than the control unit expects under the current driving conditions. I don't have reliable information on how each brand calculates the expected value, so the detail should be confirmed in the documentation. It can point to a sensor out of calibration, or to a mechanical problem or excess air. |
| Family | Powertrain (P) |
Typical symptoms
Idle higher than normal
Engine accelerating more than it should or slow to drop when you lift off
Increased fuel consumption
Jerks on gear changes, especially with an automatic gearbox
Irregular response to the pedal
Common causes
Dirty throttle body that doesn't close properly
Air leak or leaking vacuum hose
Accelerator cable or linkage with friction or play
Sensor fitted out of position
Problem with other sensors making the value look wrong, such as the air flow meter or manifold pressure sensor
What to do
How to read code P1123
This is a warning: the vehicle usually keeps working, but the control unit may limit performance (limp mode) until the fault is removed.
The code P1123 starts with P: it belongs to the powertrain (engine and transmission) area. It is defined by the manufacturer, so the exact meaning can change from make to make. The third character (1) points to fuel and air metering, and the last two (23) identify the specific fault inside that group.
How to proceed, in order
- Read the code with the diagnostic tool and note the freeze-frame data and any other stored codes.
- Check connectors, wiring and grounds of the component involved, and the battery voltage.
- Measure the real values of the component with the diagnostic tool instead of replacing it by guesswork.
- After the repair, clear the code and confirm with a road test that it does not come back.
Frequently asked questions
What does code P1123 mean?
Throttle position sensor: plausible but higher than expected. P1123 is a manufacturer-defined code. The reference definition indicates that the throttle position sensor gives a value within the normal range but higher than the control unit expects under the current driving conditions. I don't have reliable information on how each brand calculates the expected value, so the detail should be confirmed in the documentation. It can point to a sensor out of calibration, or to a mechanical problem or excess air.
Can I keep driving with code P1123 active?
With caution: limp mode possible, have it checked soon
Common causes — P1123
Throttle position sensor out of calibration or worn Dirty throttle body that doesn't close properly Air leak or leaking vacuum hose Accelerator cable or linkage with friction or play Sensor fitted out of position Problem with other sensors making the value look wrong, such as the air flow meter or manifold pressure sensor
How do you fix code P1123?
First check that the throttle body is clean and closes fully, then look for air leaks or broken vacuum hoses. Have the position read with a tester with the pedal released: it should match the rest value expected for your car. You can drive carefully, but don't wait too long.
We are ECU specialists: diagnosis, file repair and remapping for cars, bikes, trucks and agricultural vehicles.
Write to us on WhatsApp Contact us- Previous code: P1122 — Throttle position sensor: intermittent low voltage
- Next code: P1124 — Throttle position sensor: outside self-test range
Related codes
- P1100 — Mass airflow (MAF) sensor signal intermittent
- P1101 — Mass airflow (MAF) sensor out of range in self-test / KOER a...
- P1102 — Mass airflow (MAF) sensor in range but lower than expected
- P1103 — Mass airflow (MAF) sensor in range but higher than expected
- P1104 — Mass airflow (MAF) sensor ground malfunction
- P1105 — Dual alternator system fault reported (upper unit)
- P1106 — Dual alternator lower fault / MAP sensor intermittent high v...
- P1107 — Dual alternator lower fault / MAP sensor intermittent low vo...
- P1108 — Battery lamp circuit, dual alternator: malfunction
- P1109 — Intake air temperature sensor B: intermittent signal
- P1110 — Intake air temperature sensor: open or short circuit
- P1111 — Intake air temperature sensor: intermittent high voltage