P224A — NOx sensor bank 1 sensor 1: heater resistance out of range
| Meaning | The engine computer found that the electrical resistance of the internal heater of the upstream NOx (nitrogen oxides) sensor on bank 1 is outside the expected values. The heater brings the sensor up to working temperature. If it does not work properly, the sensor may read wrongly or not be ready, and emissions control suffers. The exact meaning of this code can vary slightly between manufacturers. |
| Family | Powertrain (P) |
Typical symptoms
Possible emissions system fault message
Unusual AdBlue consumption, on engines that use it
Possible power limitation on some vehicles
Worse exhaust emissions
Common causes
Damaged or corroded sensor connector or wiring
Failure of the NOx sensor as a whole
Supply or ground problem at the sensor
Rarely, a fault in the sensor's control unit or the engine computer
What to do
How to read code P224A
This is a warning: the vehicle usually keeps working, but the control unit may limit performance (limp mode) until the fault is removed.
The code P224A starts with P: it belongs to the powertrain (engine and transmission) area. It is defined by the SAE/ISO standard, so it means the same on every make. The third character (2) points to fuel and air metering (injector circuit), and the last two (4A) identify the specific fault inside that group.
How to proceed, in order
- Read the code with the diagnostic tool and note the freeze-frame data and any other stored codes.
- Check connectors, wiring and grounds of the component involved, and the battery voltage.
- Measure the real values of the component with the diagnostic tool instead of replacing it by guesswork.
- After the repair, clear the code and confirm with a road test that it does not come back.
Frequently asked questions
What does code P224A mean?
NOx sensor bank 1 sensor 1: heater resistance out of range. The engine computer found that the electrical resistance of the internal heater of the upstream NOx (nitrogen oxides) sensor on bank 1 is outside the expected values. The heater brings the sensor up to working temperature. If it does not work properly, the sensor may read wrongly or not be ready, and emissions control suffers. The exact meaning of this code can vary slightly between manufacturers.
Can I keep driving with code P224A active?
With caution: limp mode possible, have it checked soon
Common causes — P224A
Degraded internal heater in the NOx sensor Damaged or corroded sensor connector or wiring Failure of the NOx sensor as a whole Supply or ground problem at the sensor Rarely, a fault in the sensor's control unit or the engine computer
How do you fix code P224A?
First check the NOx sensor connector and wiring, especially the areas close to the exhaust. If the circuit is fine, the sensor should be tested with a suitable tool. On some cars this fault can lead to limitations, so don't delay too long.
We are ECU specialists: diagnosis, file repair and remapping for cars, bikes, trucks and agricultural vehicles.
Write to us on WhatsApp Contact us- Previous code: P2249 — O2 sensor bank 2 sensor 1: reference voltage circu...
- Next code: P224B — NOx sensor bank 1 sensor 2: heater resistance out...
Related codes
- P2200 — NOx sensor circuit fault, bank 1
- P2201 — NOx sensor circuit range/performance, bank 1
- P2202 — NOx sensor circuit low input, bank 1
- P2203 — NOx sensor circuit high input, bank 1
- P2204 — NOx sensor intermittent signal, bank 1
- P2205 — NOx sensor heater control circuit open, bank 1
- P2206 — NOx sensor heater control circuit low, bank 1
- P2207 — NOx sensor heater control circuit high, bank 1
- P2208 — NOx sensor heater sense circuit, bank 1
- P2209 — NOx sensor heater sense circuit out of range, bank 1
- P220A — Speed signal comparison implausible, Y3/6n2 and Y3/6n3
- P220B — Speed too high, Y3/6n2 or Y3/6n3