P2383 — EGR sensor D circuit: implausible or out-of-range signal
| Meaning | The control unit receives an electrical signal from the EGR sensor labelled "D", but it does not match what is expected at that moment. Which sensor "D" is depends on the manufacturer, and for some brands I have no reliable information, so check the service manual. Either the sensor itself is reading wrongly, or the EGR system is not behaving the way it is being commanded. |
| Family | Powertrain (P) |
Typical symptoms
Unstable idle or stalling at low rpm
Jerking or hesitation when accelerating
Fuel consumption different from usual
More exhaust smoke on diesels
Higher emissions at inspection
Common causes
Dirty or out-of-calibration EGR sensor
Partly blocked EGR passages or EGR cooler
Air or gas leaks in the system's pipes
Wiring or connector with abnormal resistance
Faulty sensor
What to do
How to read code P2383
This is a warning: the vehicle usually keeps working, but the control unit may limit performance (limp mode) until the fault is removed.
The code P2383 starts with P: it belongs to the powertrain (engine and transmission) area. It is defined by the SAE/ISO standard, so it means the same on every make. The third character (3) points to ignition system or misfire, and the last two (83) identify the specific fault inside that group.
How to proceed, in order
- Read the code with the diagnostic tool and note the freeze-frame data and any other stored codes.
- Check connectors, wiring and grounds of the component involved, and the battery voltage.
- Measure the real values of the component with the diagnostic tool instead of replacing it by guesswork.
- After the repair, clear the code and confirm with a road test that it does not come back.
Frequently asked questions
What does code P2383 mean?
EGR sensor D circuit: implausible or out-of-range signal. The control unit receives an electrical signal from the EGR sensor labelled "D", but it does not match what is expected at that moment. Which sensor "D" is depends on the manufacturer, and for some brands I have no reliable information, so check the service manual. Either the sensor itself is reading wrongly, or the EGR system is not behaving the way it is being commanded.
Can I keep driving with code P2383 active?
With caution: limp mode possible, have it checked soon
Common causes — P2383
EGR valve clogged with soot or partly stuck Dirty or out-of-calibration EGR sensor Partly blocked EGR passages or EGR cooler Air or gas leaks in the system's pipes Wiring or connector with abnormal resistance Faulty sensor
How do you fix code P2383?
Have a scan tool check whether the sensor reading follows the commands sent to the EGR valve, and inspect the valve and passages for deposits. The car can be used with care, but it's best to deal with it soon because deposits in the system tend to get worse.
We are ECU specialists: diagnosis, file repair and remapping for cars, bikes, trucks and agricultural vehicles.
Write to us on WhatsApp Contact us- Previous code: P2382 — EGR sensor D circuit: signal too low
- Next code: P2384 — EGR sensor D circuit: intermittent signal
Related codes
- P2300 — Ignition coil A primary control circuit low
- P2301 — Ignition coil A primary control circuit high
- P2302 — Ignition coil A secondary circuit
- P2303 — Ignition coil B primary control circuit low
- P2304 — Ignition coil B primary control circuit high
- P2305 — Ignition coil B secondary circuit
- P2306 — Ignition coil C primary control circuit low
- P2307 — Ignition coil C primary control circuit high
- P2308 — Ignition coil C secondary circuit
- P2309 — Ignition coil D primary control circuit low
- P230A — Cylinder 1 air-fuel imbalance, adjustment at limit
- P230B — Cylinder 2 air-fuel imbalance, adjustment at limit