MAN fault codes
2.462 codes with meaning, severity and what to do, from 3738 to 4061. Page 5 of 13.
- 3738 — Quantity correction value too great
- 3739 — Quantity correction value too great
- 3740 — Quantity correction value too great
- 3741 — Quantity correction value too great
- 3742 — Quantity correction value too great
- 3743 — Quantity correction value too great
- 3744 — Highside output stage exhaust gas recirculation
- 3745 — Highside output stage charge air pressure
- 3746 — Highside output stage exhaust gas
- 3747 — Highside output stage pressure governing valve
- 3748 — Highside output stage metering unit
- 3749 — Highside output stage engine air flow sensor flap
- 3750 — Highside output stage RH 07
- 3751 — Highside output stage starter relay
- 3752 — Segment encoder (camshaft)
- 3753 — Incremental encoder (crankshaft)
- 3754 — Monitoring error when system starts
- 3755 — Plausibility fuel supply pressure
- 3756 — Supply voltage sensor group 3 CY310
- 3758 — Send error message slot 2 to partner EDC
- 3759 — Send error message slot 3 to partner EDC
- 3760 — Send error message slot 4 to partner EDC
- 3761 — Send error message slot 5 to partner EDC
- 3762 — Timeout of the CAMD_ANA message
- 3763 — Timeout of the CAMD_CMOL message
- 3764 — Timeout of the CAMD_CONTROL message
- 3765 — Timeout of the CAMD_FFR1 message
- 3766 — Timeout of the CAMD_FFR2 message
- 3767 — Timeout of the CAMD_FFR3 message
- 3768 — Fault status of the CAMD_INIT message
- 3769 — Timeout of the CAMD_Limit message
- 3771 — Master / slave error in reception of
- 3772 — Monitoring terminal 15
- 3773 — Operating mode change error master/slave
- 3774 — Temporary CMOL mode of the partner EDC
- 3775 — Rail pressure monitoring
- 3776 — Excessive positive control differential
- 3777 — Excessive negative control differential
- 3778 — Rail pressure: Leakage in overrun conditions
- 3779 — Rail pressure: Leakage in quantity compensation
- 3780 — Rail pressure: High controller output when idling
- 3781 — Pressure relief valve open (pressure too high)
- 3782 — Fuel supply pressure dynamic
- 3783 — FFR (vehicle management computer) 2
- 3784 — Bit error smoke ID
- 3785 — Monitoring particle filter/PM catalytic converter
- 3786 — Particulate filter temperature limits
- 3787 — No particulate filter regeneration
- 3788 — Exhaust differential pressure
- 3789 — Exhaust differential pressure sensor
- 3790 — Exhaust differential pressure plausibility
- 3791 — Exhaust temperature before particulate filter
- 3792 — Exhaust temperature sensor before particulate filter
- 3793 — Exhaust temperature after particulate filter
- 3794 — Exhaust temperature sensor after particulate filter
- 3795 — Exhaust gas recirculation throttle butterfly
- 3797 — Highside output stage lambda probe
- 3798 — Output stage OBD lamp (MIL)
- 3799 — Highside output stage reserve 01
- 38 — Door enable display door 4
- 3800 — Air suspension/ECAS
- 3801 — Highside output stage reserve 03
- 3802 — Highside output stage stop valve compressed air
- 3803 — Engine CAN transmit error, no message
- 3804 — Engine CAN receive error, not possible to
- 3805 — Master/slave CAN communication
- 3806 — Master/slave CAN communication
- 3807 — Raise bus again
- 3808 — Vehicle management computer sends
- 3809 — ECAS malfunction
- 3810 — ECAS warning
- 3811 — ECAS governing suppression brake
- 3812 — Kneeling lowering
- 3813 — Kneeling lowering
- 3814 — Kneeling fully lowered
- 3815 — Exhaust backpressure
- 3816 — Exhaust backpressure sensor
- 3817 — Kneeling raise
- 3818 — Exhaust backpressure plausibility
- 3819 — CAN block 3
- 3820 — Byte monitoring CAN 1
- 3821 — Byte monitoring CAN 3
- 3822 — Kneeling emergency raise
- 3823 — Kneeling emergency raise
- 3824 — Kneeling emergency raise prio. 1
- 3825 — Misfiring status master
- 3826 — Kneeling lower control unit (19)
- 3827 — Kneeling door open
- 3828 — Air suspension reservoir too low
- 3829 — Air suspension reservoir too low
- 3830 — Misfiring status
- 3831 — Misfiring status
- 3832 — Misfiring status
- 3833 — Misfiring status
- 3834 — Misfiring status
- 3835 — Misfiring status
- 3836 — Lambda probe sensor acquisition
- 3837 — Lambda probe sensor acquisition
- 3838 — Lambda probe internal resistance, physical
- 3839 — Lambda probe internal resistance
- 3840 — Lowering bus below ride height
- 3841 — Bus normal level
- 3842 — Coolant pressure plausibility
- 3843 — Coolant temperature plausibility
- 3844 — NLA bellows is depressurised (p < 0.3 bar)
- 3845 — Ambient air temperature plausibility
- 3846 — Control unit configuration
- 3847 — Charge air temperature sensor ahead of motor
- 3848 — Ambient air temperature sensor
- 3849 — Catalyser not installed
- 3850 — ECAS warning flashing at 1 Hz
- 3851 — Exhaust gas recirculation flap position sensor
- 3852 — Exhaust gas recirculation temperature plausibility
- 3853 — Permanent system deviation exhaust gas recirculation
- 3854 — EDC internal temperature sensor 2
- 3855 — Lambda probe system
- 3856 — Lambda probe calibration
- 3857 — Lambda probe communication
- 3858 — Lambda probe temperature
- 3859 — Lambda probe temperature calibration
- 3860 — Turbine wheel speed
- 3861 — Turbine wheel speed sensor
- 3862 — NBF pulses without quantity requests
- 3863 — Trailing throttle monitoring
- 39 — Door enable display door 5
- 3903 — Tank/ fuel level
- 3904 — Reservoir pressure circuit 1 (too low)
- 3905 — Reservoir pressure circuit 2 (too low)
- 3906 — Reservoir pressure circuit 3 (too low)
- 3907 — Reservoir pressure circuit 4 (too low)
- 3909 — Previous circuit defective
- 3913 — ECAM in pneumatic backup, CAN OK
- 3915 — ASR engine governor failure
- 3918 — Fuel tank almost empty
- 3919 — Fill level Gas2
- 3920 — Fill level Gas3
- 4 — Expansion module door 5
- 40 — Workshop switch door 1
- 4000 — Communication fault to CRT control unit
- 4001 — Accumulator charge valve
- 4002 — Central control unit - A-controller: Internal data memory
- 4003 — Central control unit - B-controller
- 4004 — Clutch word
- 4005 — Brake lamp output
- 4006 — Central control unit - B-controller: Calculated ISC
- 4007 — ABS logic, FMI 3 = Pressure plausibility /
- 4008 — ABS (pressure control valve): Installed but no
- 4009 — Central control unit
- 4010 — Central control unit - Internal controller communication
- 4011 — ABS signals 'Not fully operational'
- 4012 — Cable fault oil temperature sensor (pin III/3 or IV/18)
- 4013 — Central control unit - A-controller, format error
- 4014 — Central control unit - Internal controller communication
- 4015 — Cable fault oil pressure sensor (pin III/4, II/5 or I/5)
- 4016 — Braking level selector
- 4017 — Central control unit EEPROM: Implausible values in
- 4018 — Central control unit EEPROM: Checksum error in
- 4019 — CAN data bus
- 4020 — Central control unit EEPROM: Checksum error in
- 4021 — Auxiliary high beam, left
- 4022 — Auxiliary high beam, right
- 4023 — CAN data bus, message TSC1 from FFR
- 4024 — CAN data bus, send system error
- 4025 — CAN data bus, BusOff
- 4026 — CAN data bus, message EBC1 from EBS/ABS
- 4027 — CAN data bus, acknowledge system error
- 4028 — CAN data bus, message EEC1 from EDC
- 4029 — CAN data bus, message TCO1 from tachograph
- 4030 — Central control unit EEPROM: Checksum error in
- 4031 — CAN data bus, message CCVS from FFR
- 4032 — CAN data bus, message ERC1_ER from EDC
- 4033 — CAN data bus, message ETC1 from gearbox
- 4034 — CAN data bus, message ETC1 from FFR
- 4035 — CAN data bus, message ETP from EDC
- 4036 — CAN data bus, message ERC1 from FFR
- 4037 — CAN data bus, message TSC1 from FFR
- 4038 — CAN data bus, time/date message from tachograph
- 4039 — Central control unit EEPROM: Implausible values in
- 4040 — Central control unit EEPROM: Checksum error in
- 4041 — CAN data bus, ABS message from EBS/ABS
- 4042 — CAN data bus, FMR1 message from FFR
- 4043 — Central control unit EEPROM: Implausible values in
- 4044 — CAN data bus, message FMR2
- 4045 — CAN data bus, message EPS
- 4046 — ALW not calibrated
- 4047 — Central control unit EEPROM: Implausible values
- 4048 — Central control unit EEPROM: Checksum error
- 4049 — Central control unit EEPROM: Checksum error
- 4050 — Brakes CAN
- 4051 — ESP sensor CAN: System bus off
- 4052 — Electrical power supply, comparison between
- 4053 — Earth 2
- 4054 — Control unit switch-off delay: Fault in electronic circuit
- 4055 — ASR: Invalid configuration
- 4056 — Additional turn indicator behind bumper
- 4057 — Clicker relay
- 4058 — Hazard warning light switch CAN
- 4059 — Hazard warning light switch external
- 4060 — Headlight high beam
- 4061 — High-beam headlight check