MAN fault codes
2.462 codes with meaning, severity and what to do, from 1 to 3080. Page 1 of 13.
- 1 — Date, time, mileage in km
- 10 — Engaged gear
- 100 — Oil pressure
- 1007 — Trip Drive Fuel Used (Natural Gas)
- 102 — Boost pressure
- 1031 — Trip Average Fuel Rate (Natural Gas)
- 1042 — ISO 11992 (trailer CAN): Data bus switched off
- 1043 — Supply voltage for peripherals
- 1045 — Gate interlock
- 105 — Charge air temperature
- 1056 — Trailer control module pressure control,
- 1057 — Central control unit - B-controller
- 1058 — Trailer control module - pressure sensor signal
- 1060 — Brake pad wear sensor signal wheel 1
- 1061 — Brake pad wear sensor signal wheel 2
- 1062 — Brake pad wear sensor signal wheel 3
- 1063 — Brake pad wear sensor signal wheel 4
- 1064 — Brake pad wear sensor signal wheel 5
- 1065 — Brake pad wear sensor signal wheel 6
- 1066 — Service brake module
- 1067 — Service brake module signal 1 (increasing)
- 1068 — Service brake module signal 2 (decreasing)
- 107 — Air filter pressure
- 1072 — Engine brake switch
- 1079 — Supply to rail pressure sensor
- 108 — Barometric Pressure
- 1080 — Supply fuel supply pressure,
- 1086 — Pressure, pressure sensor - circuit 3
- 1087 — Pressure, pressure sensor - circuit 1
- 1088 — Pressure, pressure sensor - circuit 2
- 1089 — Pressure, pressure sensor - circuit 4
- 109 — Cooling water pressure
- 1090 — Pressure, pressure sensor - circuit 5
- 11 — Cooling water temperature
- 110 — Coolant temperature
- 111 — Coolant Level
- 1131 — Charge air temperature ahead of engine
- 119 — Housing pressure
- 12 — Motor/door valve door 4 (rear)
- 120 — Temperature acquisition retarder oil
- 1210 — No text! Specific to control unit
- 1213 — Checklamp output
- 1231 — Engine CAN
- 1235 — J 1939 Network #3
- 13 — Motor/door valve door 5 (front)
- 132 — Air mass
- 1352 — Knock control cylinder 1
- 1353 — Knock control cylinder 2
- 1354 — Knock control cylinder 3
- 1355 — Knock control cylinder 4
- 1356 — Knock control cylinder 5
- 1357 — Knock control cylinder 6
- 1376 — Tl. 30-1 connected
- 14 — Motor/door valve door 5 (rear)
- 1485 — Main relay switched off
- 15 — Entry lighting door 1
- 1542 — Voltage supply metering valve
- 157 — Fuel pressure in rail
- 158 — Battery Potential (Voltage), Switched
- 159 — Gas Supply Pressure
- 16 — Entry lighting door 2
- 161 — Gearbox input speed
- 1624 — Road speed
- 1669 — A-CAN busoff
- 1673 — Status body 3 CAN
- 1675 — 'Engine start' signal
- 1676 — No 'Break light request' signal in ERC_RX (timeout)
- 168 — Battery voltage
- 17 — Entry lighting door 3
- 171 — Outside temperature
- 173 — Exhaust temperature before particulate filter
- 174 — Fuel temperature
- 175 — Engine oil temperature
- 1761 — Urea fill level tank
- 177 — Transmission fluid temperature
- 18 — Entry lighting door 4
- 19 — Entry lighting door 5
- 190 — Engine speed
- 191 — Gearbox output speed
- 2 — Engine Speed
- 20 — Door closing warning device door 1
- 2000 — No text! Specific to control unit
- 2001 — EDC slave not on CAN
- 2003 — Gearbox not on CAN
- 2009 — MAN Hydro Drive control unit not on CAN
- 2011 — EBS not on CAN (pneumatic backup operation)
- 2015 — Retarder engine not on CAN
- 2016 — Driveline retarder not on CAN
- 2023 — Instrumentation not on CAN
- 2037 — Radio module not on CAN
- 2039 — FFR not on CAN
- 2042 — ACC not on CAN
- 2047 — ECAS not on CAN
- 2048 — ECAM not on CAN
- 2051 — Tyre pressure control system (TPM) not on CAN
- 2061 — Control unit of the exhaust post-treatment not on CAN
- 2062 — ESP not on CAN
- 2064 — ECAS 2 not on CAN
- 21 — Door closing warning device door 2
- 2114 — VSM not on CAN
- 2120 — ZFR not on CAN
- 22 — Door closing warning device door 3
- 2232 — Lane guard system not on CAN
- 2238 — Tachograph not on CAN
- 2251 — Telematic onboard module not on CAN
- 2253 — KSM not on CAN
- 228 — Speed speedometer and sensor
- 23 — Door closing warning device door 4
- 24 — Door closing warning device door 5
- 245 — Vehicle mileage
- 25 — Ramp activation door 1
- 26 — Ramp activation door 2
- 27 — Ramp activation door 3
- 28 — Ramp activation door 4
- 29 — Ramp activation door 5
- 2987 — Parameter record in central on-board computer 2
- 2999 — Power limit (temperature adaptation)
- 3 — Expansion module door 4
- 30 — Stop request display door 1
- 3000 — An unexpected RESET has occurred
- 3001 — Additional information 1
- 3002 — Additional information 2
- 3003 — Additional information 3
- 3004 — Additional information 4
- 3005 — CAN data bus: Time overrun when receiving
- 3006 — CAN data bus, TSC1 - message
- 3007 — Bypass flap motor
- 3008 — Blower control voltage
- 3009 — CAN data bus
- 3010 — CAN data bus, start error monitoring
- 3011 — Angle of injection start
- 3012 — CAN data bus: Time overrun when receiving
- 3013 — Axial thrust (outside tolerance)
- 3014 — Camera module too hot
- 3015 — Control unit (checksum permitted axle loads)
- 3016 — Control unit
- 3017 — Control unit (watchdog)
- 3018 — Control unit (EEPROM parameter)
- 3019 — Control unit (internal relay voltage supply or
- 3020 — Accelerator pedal, PWM1 signal
- 3021 — Accelerator pedal, PWM2 signal
- 3022 — Accelerator pedal, PWM1 and PWM2 signal
- 3023 — CAN data bus: Time overrun when receiving
- 3024 — Brake pad wear: Incorrect tendency between the axles
- 3025 — Brake pad wear: Incorrect tendency
- 3026 — Brake pad wear: Incorrect tendency
- 3027 — Brake pad wear: Incorrect tendency
- 3028 — Brake pad wear: Incorrect tendency
- 3029 — 'Request engine speed increase in
- 3030 — CAN data bus retarder configuration
- 3031 — Adjustment lever angle reduction input
- 3032 — CAN data bus engine brake configuration,
- 3033 — CAN data bus engine brake configuration,
- 3034 — Actuator test of axle behaviour in centring circuit,
- 3035 — Actuator test of pressure behaviour in centring circuit
- 3036 — CAN data bus: Time overrun when receiving
- 3037 — CAN data bus: Time overrun when
- 3038 — CAN data bus: Time overrun when
- 3039 — CAN data bus: Time overrun when
- 3040 — Angle encoder configuration
- 3041 — Angle encoder supply
- 3042 — Angle encoder, steering axle 1, differential
- 3043 — Angle encoder, steering axle 1, total voltage
- 3044 — Angle encoder, steering axle 1
- 3045 — Angle encoder, steering axle 1, track 1
- 3046 — Angle encoder, steering axle 1, track 2
- 3047 — Angle encoder, steering axle 2, differential
- 3048 — Angle encoder, steering axle 2, total voltage
- 3049 — Angle encoder, steering axle 2
- 3050 — After-run test, zero quantity
- 3051 — After-run test, MES1 output
- 3052 — Angle encoder, steering axle 3, differential
- 3053 — Angle encoder, steering axle 3, total voltage
- 3054 — Angle encoder, steering axle 3
- 3055 — Angle encoder, steering axle 3, track 1
- 3056 — Angle encoder, steering axle 3, track 2
- 3057 — Angle encoder, steering axle 4, differential
- 3058 — Angle encoder, steering axle 4, total voltage
- 3059 — Angle encoder, steering axle 4
- 3060 — Angle encoder, steering axle 4, track 1
- 3061 — Angle encoder, steering axle 4, track 2
- 3062 — Angle encoder, front axle, differential
- 3063 — After-run not completed
- 3064 — Angle encoder, front axle
- 3065 — Angle encoder, front axle, track 1
- 3066 — Angle encoder, front axle, track 2
- 3067 — Angle encoder, joystick, differential
- 3068 — Angle encoder, joystick, total voltage
- 3069 — Angle encoder, joystick
- 3070 — Angle encoder, joystick, track 1
- 3071 — Angle encoder, joystick, track 2
- 3072 — Driveline CAN databus, receive time exceeded
- 3073 — Amount violation sign
- 3074 — Can message 'Wheel speed information 2'
- 3075 — Driveline CAN databus, receive time exceeded
- 3076 — Driveline CAN databus, receive time exceeded
- 3077 — CAN data bus driveline, message XBR (ACC)
- 3078 — CAN data bus driveline, message ETC7
- 3079 — Governor linkage position
- 3080 — CAN message CCVS