P1124 — Throttle position sensor: outside self-test range
| Meaning | P1124 is a manufacturer-defined code. The reference definition indicates that the throttle position sensor fell outside the expected range during the automatic self-test the control unit runs with the key on. I don't have reliable information on how each brand runs this test, so the detail should be confirmed in the documentation. In practice, with the pedal released the sensor gives a value the control unit doesn't consider normal. |
| Family | Powertrain (P) |
Typical symptoms
Rough idle, too high or too low
Irregular or hesitant acceleration
Automatic gearbox shifting abnormally
Possible limp mode with reduced power
Uncertain starting
Common causes
Connector or wiring with abnormal resistance
Dirty throttle body that doesn't return fully to its rest position
Pedal or accelerator cable not releasing fully
Degraded sensor supply or ground
Control unit input fault (rare)
What to do
How to read code P1124
This is a warning: the vehicle usually keeps working, but the control unit may limit performance (limp mode) until the fault is removed.
The code P1124 starts with P: it belongs to the powertrain (engine and transmission) area. It is defined by the manufacturer, so the exact meaning can change from make to make. The third character (1) points to fuel and air metering, and the last two (24) identify the specific fault inside that group.
How to proceed, in order
- Read the code with the diagnostic tool and note the freeze-frame data and any other stored codes.
- Check connectors, wiring and grounds of the component involved, and the battery voltage.
- Measure the real values of the component with the diagnostic tool instead of replacing it by guesswork.
- After the repair, clear the code and confirm with a road test that it does not come back.
Frequently asked questions
What does code P1124 mean?
Throttle position sensor: outside self-test range. P1124 is a manufacturer-defined code. The reference definition indicates that the throttle position sensor fell outside the expected range during the automatic self-test the control unit runs with the key on. I don't have reliable information on how each brand runs this test, so the detail should be confirmed in the documentation. In practice, with the pedal released the sensor gives a value the control unit doesn't consider normal.
Can I keep driving with code P1124 active?
With caution: limp mode possible, have it checked soon
Common causes — P1124
Throttle position sensor out of calibration or faulty Connector or wiring with abnormal resistance Dirty throttle body that doesn't return fully to its rest position Pedal or accelerator cable not releasing fully Degraded sensor supply or ground Control unit input fault (rare)
How do you fix code P1124?
Check that the pedal and cable return fully to rest and that the throttle body is clean, then check the sensor connector and wires. A tester can read the value with the pedal released to see whether the sensor is out of calibration. If the car has little power, drive carefully and have it checked soon.
We are ECU specialists: diagnosis, file repair and remapping for cars, bikes, trucks and agricultural vehicles.
Write to us on WhatsApp Contact us- Previous code: P1123 — Throttle position sensor: plausible but higher tha...
- Next code: P1125 — Throttle position sensor: intermittent signal
Related codes
- P1100 — Mass airflow (MAF) sensor signal intermittent
- P1101 — Mass airflow (MAF) sensor out of range in self-test / KOER a...
- P1102 — Mass airflow (MAF) sensor in range but lower than expected
- P1103 — Mass airflow (MAF) sensor in range but higher than expected
- P1104 — Mass airflow (MAF) sensor ground malfunction
- P1105 — Dual alternator system fault reported (upper unit)
- P1106 — Dual alternator lower fault / MAP sensor intermittent high v...
- P1107 — Dual alternator lower fault / MAP sensor intermittent low vo...
- P1108 — Battery lamp circuit, dual alternator: malfunction
- P1109 — Intake air temperature sensor B: intermittent signal
- P1110 — Intake air temperature sensor: open or short circuit
- P1111 — Intake air temperature sensor: intermittent high voltage