OBD-II Powertrain (P) fault codes
8.028 codes with meaning, severity and what to do, from P1209 to P1447. Page 20 of 41.
- P1209 — Injector control pressure system fault
- P1210 — Injector control pressure above expected level
- P1211 — Injector control pressure sensor out of range
- P1212 — Injector control pressure not detected during cranking
- P1213 — Start injector circuit malfunction
- P1214 — Accelerator pedal sensor B intermittent signal
- P1215 — Accelerator pedal sensor C signal too low
- P1216 — Accelerator pedal sensor C signal too high
- P1217 — Accelerator pedal sensor C intermittent signal
- P1218 — CID signal too high
- P1219 — CID signal too low
- P1220 — Series throttle control system malfunction
- P1221 — Traction control system malfunction
- P1222 — Traction control output circuit malfunction
- P1223 — Pedal demand sensor B signal too high
- P1224 — Throttle position sensor B out of self-test range
- P1225 — Injector needle lift sensor malfunction
- P1226 — Control sleeve sensor malfunction
- P1227 — Wastegate stuck closed (overboost)
- P1228 — Wastegate stuck open, boost pressure too low
- P1229 — Intercooler pump control circuit fault
- P1230 — Fuel pump low-speed operation malfunction
- P1231 — Fuel pump secondary circuit low, high-speed mode
- P1232 — Fuel pump speed primary circuit malfunction
- P1233 — Fuel pump driver module not responding
- P1234 — Fuel pump driver module off line
- P1235 — Fuel pump control out of range
- P1236 — Fuel pump control out of range (variant)
- P1237 — Fuel pump secondary circuit malfunction
- P1238 — Fuel pump secondary circuit fault (variant)
- P1239 — Speed-controlled fuel pump positive feed fault
- P1240 — Sensor power supply malfunction
- P1241 — Sensor power supply voltage too low
- P1242 — Sensor power supply voltage too high
- P1243 — Second fuel pump faulty or short to ground
- P1244 — Alternator load input signal too high
- P1245 — Alternator load input signal too low
- P1246 — Alternator load input signal failure
- P1247 — Turbo boost pressure too low
- P1248 — Turbo boost pressure not detected
- P1249 — Wastegate control valve performance fault
- P1250 — PRC solenoid circuit malfunction
- P1251 — Air mixture solenoid circuit malfunction
- P1252 — Pedal correlation: PDS1 and LPDS, high
- P1253 — Pedal correlation: PDS1 and LPDS, low
- P1254 — Pedal correlation: PDS2 and LPDS, high
- P1255 — Pedal correlation: PDS2 and LPDS, low
- P1256 — Pedal correlation: PDS1 and HPDS disagree
- P1257 — Pedal correlation: PDS2 and HPDS disagree
- P1258 — Pedal correlation: PDS1 and PDS2 disagree
- P1259 — Immobilizer to engine control unit signal error
- P1260 — Theft attempt detected, vehicle immobilized
- P1261 — Cylinder 1: short between high side and low side
- P1262 — Cylinder 2: short between high side and low side
- P1263 — Cylinder 3: short between high side and low side
- P1264 — Cylinder 4: short between high side and low side
- P1265 — Cylinder 5: short between high side and low side
- P1266 — Cylinder 6: short between high side and low side
- P1267 — Cylinder 7: short between high side and low side
- P1268 — Cylinder 8 injector circuit short between high and low side
- P1269 — Immobilizer code not programmed
- P1270 — Engine RPM or speed limiter reached
- P1271 — Cylinder 1 injector circuit open
- P1272 — Cylinder 2 injector circuit open
- P1273 — Cylinder 3 injector circuit open
- P1274 — Cylinder 4 injector circuit open
- P1275 — Cylinder 5 injector circuit open
- P1276 — Cylinder 6 injector circuit open
- P1277 — Cylinder 7 injector circuit open
- P1278 — Cylinder 8 injector circuit open
- P1280 — Injection control pressure too low
- P1281 — Injection control pressure too high
- P1282 — Excessive injection control pressure
- P1283 — IPR pressure regulator circuit fault
- P1284 — Self-test aborted due to injection control pressure fault
- P1285 — Cylinder head temperature too high
- P1286 — Fuel pulse in range but lower than expected
- P1287 — Fuel pulse in range but higher than expected
- P1288 — Cylinder head temperature sensor out of self-test range
- P1289 — Cylinder head temperature sensor: signal too high
- P1290 — Cylinder head temperature sensor: signal too low
- P1291 — Bank 1 injectors: supply side shorted
- P1292 — Bank 2 injectors: supply side shorted
- P1293 — Bank 1 injectors: supply circuit open
- P1294 — Bank 2 injectors open / idle target not reached
- P1295 — Bank 1 multiple faults including low side shorts
- P1296 — Bank 2 multiple faults including low side shorts
- P1297 — Injector supply sides shorted together
- P1298 — Injector driver module (IDM) failure
- P1299 — Cylinder head overtemperature protection active
- P1300 — Boost pressure calibration fault
- P1301 — Boost calibration reading too high
- P1302 — Boost calibration reading too low
- P1303 — EGR valve calibration fault
- P1304 — EGR calibration reading too high
- P1305 — EGR calibration reading too low
- P1306 — Kickdown relay: pull-in circuit fault
- P1307 — Kickdown relay: hold circuit fault
- P1308 — A/C compressor clutch circuit fault
- P1309 — Internal misfire-monitor circuit fault
- P1313 — Misfire rate high enough to damage catalyst - bank 1
- P1314 — Misfire rate high enough to damage catalyst - bank 2
- P1315 — Persistent engine misfire
- P1316 — Injector circuit or ignition diagnostic module codes detected
- P1317 — Injector circuit or ignition module codes not updated
- P1336 — Crankshaft and camshaft sensor signals not consistent
- P1340 — Camshaft position sensor B circuit fault
- P1341 — Camshaft position sensor B signal out of range
- P1345 — Camshaft sensor circuit or crank-cam correlation fault
- P1346 — Fuel level sensor B circuit fault
- P1347 — Fuel level sensor B signal out of range
- P1348 — Fuel level sensor B circuit low
- P1349 — Fuel level sensor B circuit high
- P1350 — Fuel level sensor B intermittent or bypass line monitor
- P1351 — Ignition diagnostic module input or coil control circuit high voltage
- P1352 — Ignition coil A primary circuit fault
- P1353 — Ignition coil B primary circuit fault
- P1354 — Ignition coil C primary circuit fault
- P1355 — Ignition coil D primary circuit fault
- P1360 — Ignition coil A: secondary circuit fault
- P1361 — Ignition control circuit: low voltage
- P1362 — Ignition coil C: secondary circuit fault
- P1363 — Ignition coil D: secondary circuit fault
- P1364 — Ignition coil: primary circuit failure
- P1365 — Ignition coil: secondary circuit failure
- P1366 — Ignition: manufacturer spare code
- P1367 — Ignition: manufacturer spare code
- P1368 — Ignition: manufacturer spare code
- P1369 — Engine temperature light: monitoring fault
- P1370 — Insufficient RPM rise during spark test
- P1371 — Ignition coil cylinder 1: early activation
- P1372 — Ignition coil cylinder 2: early activation
- P1373 — Ignition coil cylinder 3: early activation
- P1374 — Crank sensor / coil cylinder 4: early activation
- P1375 — Ignition coil cylinder 5: early activation
- P1376 — Ignition coil cylinder 6: early activation
- P1380 — Misfire detected: rough road data not available
- P1381 — Variable cam timing overadvanced / misfire detected
- P1382 — Variable cam timing solenoid 1: circuit fault
- P1383 — Variable cam timing over-retarded (bank 1)
- P1384 — Variable valve timing solenoid A malfunction
- P1385 — Variable valve timing solenoid B malfunction
- P1386 — Variable cam timing over-advanced (bank 2)
- P1387 — Variable cam timing solenoid #2 circuit malfunction
- P1388 — Variable cam timing over-retarded (bank 2)
- P1389 — Glow plug circuit: low voltage on the supply side
- P1390 — Octane adjust pin out of self-test range
- P1391 — Glow plug circuit low input (bank 1)
- P1392 — Glow plug circuit high input (bank 1)
- P1393 — Glow plug circuit low input (bank 2)
- P1394 — Glow plug circuit high input (bank 2)
- P1395 — Glow plug monitor fault (bank 1)
- P1396 — Glow plug monitor fault (bank 2)
- P1397 — System voltage out of self-test range
- P1398 — Variable valve timing solenoid B circuit high input
- P1399 — Glow plug circuit: high signal on the supply side
- P1400 — EGR differential pressure sensor: low signal
- P1401 — EGR differential pressure sensor: high signal
- P1402 — EGR metering orifice restricted
- P1403 — EGR differential pressure sensor hoses reversed
- P1404 — Intake air temp sensor circuit or EGR closed-position fault
- P1405 — Upstream EGR pressure sensor hose off or blocked
- P1406 — EGR position sensor performance fault
- P1407 — No EGR flow detected
- P1408 — EGR flow outside self-test range
- P1409 — EGR vacuum regulator control circuit fault
- P1411 — Secondary air system incorrect downstream flow
- P1413 — Secondary air system monitor circuit low input
- P1414 — Secondary air system monitor circuit high input
- P1415 — Secondary air pump circuit fault, bank 1
- P1416 — Secondary air circuit fault, bank 2
- P1417 — Secondary air relief valve circuit fault
- P1418 — Split air circuit 1 fault
- P1419 — Split air circuit 2 fault
- P1420 — Catalyst temperature sensor failure
- P1421 — Catalyst damage
- P1422 — EGI temperature sensor failure
- P1423 — EGI functionality test failed
- P1424 — EGI glow plug primary failure
- P1425 — Glow plug system secondary fault (manufacturer-defined)
- P1426 — Air mass sensor (EGI Mini) signal out of range
- P1427 — Air mass sensor (EGI Mini) short circuit
- P1428 — Air mass sensor (EGI Mini) open circuit
- P1429 — Electric air pump primary fault (manufacturer-defined)
- P1430 — Electric air pump secondary fault (manufacturer-defined)
- P1433 — A/C refrigerant temperature sensor signal low
- P1434 — A/C refrigerant temperature sensor signal high
- P1435 — A/C refrigerant temperature sensor reading implausible
- P1436 — A/C evaporator air temperature sensor signal low
- P1437 — A/C evaporator air temperature sensor signal high
- P1438 — A/C evaporator air temperature sensor reading implausible
- P1439 — Floor temperature switch circuit fault
- P1440 — Fuel vapour purge valve stuck open
- P1441 — EVAP flow while valve should be closed (manufacturer-defined, Chevrole...
- P1442 — Leak in the fuel vapour recovery (EVAP) system
- P1443 — EVAP system control valve fault (manufacturer-defined)
- P1444 — EVAP purge flow sensor signal low
- P1445 — EVAP purge flow sensor signal high
- P1446 — EVAP vacuum solenoid circuit fault
- P1447 — EVAP system closure valve flow fault